Interspeed Light Blue 2.5LT

CODE: YBA331/2.5

List price: ~~€165.00~~

Price: €127.95

You save: €37.05 (22%)

-22%

Quantity:

Add to wish list Add to compare list

Description
Tags
Send to friend

Product Description

No longer just extra strong, a new, improved formula makes this superior antifouling ultra strong. Containing Teflon® it provides a smoother, harder, more slippery surface which deters fouling attachment for a clean, slick hull. It is ideal for high-speed crafts or craft on drying moorings. Can be burnished. Contains Biolux and Teflon® which are EXCLUSIVELY available in antifoulings from International.

Contains Copper Oxide and Preventol A4S

Coverage: 7sq.m/750ml and 23.5sq.m/2.5lt

Application Details - Interspeed Ultra

Area	Underwater hull
Finish/Sheen	Matt
Thinner:	YTA085
Number of Coats:	2-3 by brush/roller
Method of application:	Airless Spray / Airmix / Brush / Roller

Pack sizes:	750 ml / 2.5 Lt
Suitable for high speed craft?	YES

PRODUCT DESCRIPTION

Offers protection in the highest fouling conditions where a hard, scrubbable antifouling is required. Ideal for fast powerboats.
* High strength, hard antifouling
* Hard, scrubbable finish to allow clean-off if needed
* Suitable for burnishing to provide a smooth finish
* Smooth finish for maximum slip through the water

PRODUCT INFORMATION

Colour	YBA331-Light Blue
Finish	Matt
Specific Gravity	1.5
Volume Solids	45% average
Typical Shelf Life	2 yrs
VOC (As Supplied)	485 g/lt
Unit Size	750 ml 2.5 Lt

DRYING/OVERCOATING INFORMATION


Drying
5ºC	15ºC	23ºC	35ºC

Touch Dry [ISO]	1hrs	45mins	30mins	20mins
Immersion	24hrs	12hrs	8hrs	6hrs

Note:Max. Immersion Times are as follows: 5-15ºC - 3 mths; 23ºC - 2 mths; 35ºC - 1 mth

	Overcoating
	Substrate Temperature
5ºC		15ºC		23ºC		35ºC
Overcoated By	Min	Max	Min	Max	Min	Max	Min	Max

Interspeed Ultra	16hrs	ext	10hrs	ext	6hrs	ext	4hrs	ext
Micron 66	16hrs	ext	10hrs	ext	6hrs	ext	4hrs	ext
Micron Extra (Professional)	16hrs	ext	10hrs	ext	6hrs	ext	4hrs	ext

APPLICATION AND USE

Preparation	PREVIOUSLY ANTIFOULED SURFACE: In Good Condition: Rinse with fresh water and allow to dry. If old antifouling is incompatible or unknown, seal with Primocon. In Poor Condition: Use Interstrip to remove all traces of antifouling. PRIMING: All preparation for bare substrates is covered on the appropriate primer datasheet. BARE GRP: Gelshield 200 for osmosis protection, or Primocon. STEEL/IRON: Prime with Interprotect or Primocon. LEAD: Etch Primer followed by Interprotect or Primocon. WOOD: Preserve, if required, with Intertox. Prime with Interprotect or Primocon.

Method	Apply two coats per season.

Hints	Mixing Stir well before use. Thinner YTA085 Thinners No.3 Thinning Thinning is not recommended. Cleaner YTA085 Thinners No.3 Other True colour will develop after immersion. Take care to apply all the paint calculated even if it means applying an extra coat. It is important for performance to apply the correct thickness.

Some Important Points	To prevent premature failure, ensure the correct amount of paint is applied using the coverage as a guide. Product temperature should be minimum -5ºC and maximum 35ºC. Ambient temperature should be minimum -5ºC and maximum 35ºC. Substrate temperature should be minimum 1ºC above dew point and maximum 35ºC.

Compatibility/Substrates	GRP, Wood, Steel/Iron, Lead. Not suitable for use over Aluminium/Alloy substrates or zinc sprayed surfaces. Can be applied direct over most types of antifoulings, provided they are in sound condition.

Number of Coats	2-3 by brush/roller

Coverage	(Theoretical) - 10.50 (mÂ²/lt) by brush
	(Practical) - 9.40 (mÂ²/lt)

Recommended DFT	43 microns dry
Recommended WFT	96 microns wet

Application Methods	Brush, Roller , AIRLESS SPRAY NOT RECOMMENDED

TRANSPORTATION,STORAGE AND SAFETY INFORMATION

Storage	GENERAL INFORMATION: Exposure to air and extremes of temperature should be avoided. For the full shelf life of Interspeed Ultra to be realised ensure that between use the container is firmly closed and the temperature is between 5ºC/40ºF and 35ºC/95ºF. Keep out of direct sunlight. TRANSPORTATION: Interspeed Ultra should be kept in securely closed containers during transport and storage.

Safety	GENERAL: Contains biocides. Antifoulings should only be wet sanded. Never dry sand or burn-off old antifoulings. Read the label safety section for Health and Safety Information, also available from our Technical Help Line. DISPOSAL: Do not discard tins or pour paint into water courses, use the facilities provided. It is best to allow paints to harden before disposal. Remainders of Interspeed Ultra cannot be disposed of through the municipal waste route or dumped without permit. Disposal of remainders must be arranged for in consultation with the authorities.

IMPORTANT NOTES

The information given in this sheet is not intended to be exhaustive. Any person using the product without first making further written enquiries as to the suitability of the product for the intended purpose does so at their own risk and we can accept no responsibility for the performance of the product or for any loss or damage (other than death or personal or injury resulting from negligence) arising out of such use. The information contained in this sheet is liable to modification from time to time in the light of experience and our policy of continuous product development.

and International are registered trademarks of Akzo Nobel.